Subaru Outback (BR): Warning Light Illumination Pattern
A: INSPECTION
- Ignition switch
- OFF
- ON
- Engine start
- ABS warning light
- Light OFF
- Light ON
- 2 sec.
- VDC OFF indicator light
- VDC warning light & VDC indicator light
- Several seconds (depending on engine coolant temperature)
- Brake warning light (EBD warning light)
- Parking brake
- Released
1) When warning lights or indicator lights do not illuminate in accordance with this illumination pattern, there must be an electrical malfunction.
2) When warning lights or indicator lights remain constantly OFF, check the combination meter circuit or CAN communication circuit. <Ref. to VDC(diag)-28, ABS WARNING LIGHT, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON, Warning Light Illumination Pattern.>
3) When the ABS warning light, VDC OFF indicator light, and VDC warning light & VDC indicator light do not go off, check the combination meter circuit or CAN communication circuit. <Ref. to VDC(diag)- 29, ABS WARNING LIGHT DOES NOT GO OFF, Warning Light Illumination Pattern.> <Ref. to VDC(diag)-31, VDC OFF INDICATOR LIGHT DOES NOT GO OFF, Warning Light Illumination Pattern.> <Ref. to VDC(diag)-30, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT GO OFF, Warning Light Illumination Pattern.>
4) When the brake warning light blinks and the hill hold indicator light illumination is faulty, check the parking brake system. <Ref. to PB(diag)-2, Basic Diagnostic Procedure.>
NOTE:
- Even though the ABS warning light, and the VDC
warning light & VDC indicator light do not go off in 2
seconds after illuminating, the ABS and VDC functions
are normal if the warning lights go off while the
vehicle is driven at approximately 12 km/h (7 MPH).
However, while these lights are on, the functions with their warning lights illuminated do not operate.
- It may take several minutes before the VDC warning light & VDC indicator light goes off, if the vehicle is parked under low temperature for a specified time. This is not defective because it is resulted from low engine coolant temperature. If DTC is recorded at this time, perform the Clear Memory Mode. <Ref. to VDC(diag)-25, Clear Memory Mode.>
- With the vehicle jack-up/lift-up or set on free rollers,
when the wheels lock or spin after starting the
engine, ABS warning light, and VDC warning light
& VDC indicator light may illuminate because VDCCM&
H/U detects the abnormal conditions from
ABS wheel speed sensors. In this case, this is not a
malfunction. Perform the Clear Memory Mode.
<Ref. to VDC(diag)-25, Clear Memory Mode.>
B: ABS WARNING LIGHT, VDC OFF INDICATOR LIGHT, VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT COME ON
DETECTING CONDITION:
- Defective combination meter
- Defective CAN communication
TROUBLE SYMPTOM:
When the ignition switch is turned to ON (engine OFF), ABS warning light, VDC OFF indicator light, and VDC warning light & VDC indicator light do not illuminate.
NOTE: When pressing the VDC OFF switch for 10 seconds or more, the VDC OFF indicator light goes off and cannot operate any more. When turning the ignition switch from OFF to ON, the OFF operation enabled status is restored.
C: ABS WARNING LIGHT DOES NOT GO OFF
DETECTING CONDITION:
- Defective combination meter
- Defective CAN communication
TROUBLE SYMPTOM:
When starting the engine, the ABS warning light is kept ON.
D: VDC WARNING LIGHT AND VDC INDICATOR LIGHT DO NOT GO OFF
DETECTING CONDITION:
- Defective combination meter
- Defective engine
- Defective CAN communication
TROUBLE SYMPTOM:
When starting the engine, the VDC warning light & VDC indicator light remains lit.
E: VDC OFF INDICATOR LIGHT DOES NOT GO OFF
DETECTING CONDITION:
- Defective combination meter
- Defective CAN communication
- VDC OFF switch is shorted.
TROUBLE SYMPTOM:
When starting the engine, VDC OFF indicator light is kept ON.
NOTE: When pressing the VDC OFF switch for 10 seconds or more, the VDC OFF indicator light goes off and cannot operate any more. When turning the ignition switch from OFF to ON, the OFF operation enabled status is restored.
F: BRAKE WARNING LIGHT DOES NOT GO OFF
DETECTING CONDITION:
- Brake warning light circuit is shorted.
- Defective sensor/connector
TROUBLE SYMPTOM:
After starting the engine, the brake warning light remains lit though the parking lever is released.
NOTE: When brake warning light blinks, check the parking brake system. <Ref. to PB(diag)-2, Basic Diagnostic Procedure.>
WIRING DIAGRAM:
READ NEXT:
Vehicle Dynamics Control - List of Diagnostic Trouble Code (DTC)
A: LIST
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
A: DTC C0021 FRONT RIGHT ABS SENSOR CIRCUIT OPEN OR SHORT
NOTE: For the diagnostic procedure, refer to "DTC C0027 REAR L
General Description of Brakes
A: SPECIFICATION
NOTE: Refer to "PB" section for parking brake specifications. <Ref. to PB-2, SPECIFICATION, General Description.>
B: COMPONENT
1. FRONT DISC BRAKE
16-
SEE MORE:
Oil Seal
A: INSPECTION
Check for transmission gear oil leaks at oil seal area.
If there is an oil leak, replace the oil seal with
new one and check the propeller shaft.
B: REPLACEMENT
1) Remove the collector cover. (turbo model)
2) Lift up the vehicle.
3) Remove the front under cover. <Ref. to EI-35,
Battery drainage prevention function
If a door or the rear gate (Outback) is not completely closed, the interior lights
will remain illuminated as a result. However, several lights are automatically turned
off by the battery drainage prevention function to prevent the battery from going
dead. The following interior lights are aff
